The Best The Alfa Romeo Giulietta

Warm tips:
Pls firstly compare the size and shape as the pictures shown with the push start button of your car before purchasing;
If you are still not sure, please kindly contact us firstly, thank you!!!
When sticking, pls make sure the sticker is sticked on the Correct / Center position of car engine start stop button,
then start and stop you car for 3-5 times to make sure all is ok after installation
Do not wash your car within 24 hours after installed
You can also use the hair dryer to warm up the 3M adhesive tape before instal to make the item stick tightly

Features:
– Color brilliant and optional, personalize selection bring you unique visual experience, and makes your car looking more cool than before
– Easy to instal, no need to disassemble the car engine start stop button, just stick it on the button
– Strong viscosity, not easy to fall off, prevent the push button from scratches and abrasions
– No residue and no damaging to your car

Installation:
1) keep the surface clean and dry before installation
2) tear the adhesive tape off and stick onto the right position slowly
3) press it slightly for 1-2 minutes

Compatible Vehicles:
Fit For Alfa Romeo Giulietta Stelvio Mito 147 156 159 166

Car Engine Start Stop Button Cover
Color: Silver
Material: Aluminum Alloy
Cover Size: Diameter: 2.2cm/0.87inch
Instal location: Car Engine Start Stop Button

Package:
1 × Car Engine Start Stop Button Cover

Italian Flag emblem is Approx. Width 2.91" inches x Height 1.26" inches [74 mm x 32.0 mm]. The emblem is made of ABS on high-quality, aircraft aluminum and hard-anodized finish for a long-lasting result. It comes with self-adhesive 3M tape for easy, simple installation. It can be installed in ANY smooth surface inside or outside any vehicle. Imported from Japan. You can install this emblem on the trunk, fenders, interior console, etc. *Note: Some emblems also look great on cell phones, laptops and computers. **Note: Surface must be clean and dry prior to adhering. ***NOTE: Please Note that these are NOT the cheap Vinyl and Decal Emblems sold all by most on the Internet. The Emblem is made of high quality ALUMINUM and is noticeably different.

Compatibility: (Only for Alfa Romeo)
Alfa Romeo Giulietta (2011 — 2018);

Alfa Romeo Mito (2009 — 2018);

Alfa Romeo Stelvio (2017 — 2018);

Alfa Romeo Giulia (2017 — 2018);

Alfa Romeo 159 (2004 — 2012);

Alfa Romeo Brera (2005 — 2010);

Alfa Romeo Spider (2006 — 2010);

Installation Instructions:
1. Use A Flathead Screwdriver Or Installation Tool To Remove And Disconnect Original Door Step Lights .
2. Plug In new Door Lights With Correspondent Connector.
3. Put new Door Lights To The Spot Where Your Original Step Lights Were.
4. Alfa Logo Should Be Projecting On To The Ground.

Package Include:

2 pieces Alfa welcome light

The Relentless Pursuit of perfection Alfa

Set yourself apart from the crowd with a WFB Car Door Projector that reflects your tastes and passions. Be prepared to get tons of compliments every time you take it out with you!

Features :
1. Direct replacement.No modifications required.No wire cutting. No error or warning on dashboard.
2 . Never used or tried on , Simple installation.Can be done in 5 minutes
3. Voltage:12V with 2000L.

Compatibility: (Only for Alfa Romeo)
Alfa Romeo Giulietta (2011 — 2018);
Alfa Romeo Mito (2009 — 2018);
Alfa Romeo Stelvio (2017 — 2018);
Alfa Romeo Giulia (2017 — 2018);
Alfa Romeo 159 (2004 — 2012);
Alfa Romeo Brera (2005 — 2010);
Alfa Romeo Spider (2006 — 2010);

Installation Instructions:
1. Use A Flathead Screwdriver Or Installation Tool To Remove And Disconnect Original Door Step Lights .
2. Plug In new Door Lights With Correspondent Connector.
3. Put new Door Lights To The Spot Where Your Original Step Lights Were.
4. Alfa Logo Should Be Projecting On To The Ground.

Package Include:

Description:
Fit For Alfa Romeo Giulietta Stelvio Mito 147 156 159 166

Material :Aluminum Alloy
Cover’s Diameter: 2.2 cm (Approx)

Package Included: 1pc Cover

Installation:
Easy installed and No modification needed, 3M tape is at the back.
1. Please clean the surface before installation.
2. Compare the position and adjust it.
3. Tear off the sticker and stick it.
4. Press it to make it stick strongly.

Attention:
1.Describe size with the actual size maybe has 0.1 cm error, Please Subject to actual goods size，thanks!!!
2.The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding.

Brand Name : YONG XUN
Sticker Placement : Head
Design : cartoon
Model : Vehicle Logo
Material Type : Other
Type : Aluminum Sticker
Item Type : Stickers
Item Length : 0inch
Item Height : 0inch
Item Diameter : 0inch
Type Of Sticker : Car Body
Category : Emblems
Model Name : yu hai
Item Width : 0inch